Roundtable

roundtable@muug.ca

4 participants
2589 discussions

MUUG Meeting, Dec 11, 7:30PM -- Using Kickstart to Install Red Hat
by gedetil＠cs.umanitoba.ca 04 Dec '01

04 Dec '01

[Posted to man.unix.general and other news groups] ------ Forwarded Article <9uiurk$jfu$1(a)canopus.cc.umanitoba.ca> ------ From gedetil(a)cs.umanitoba.ca (Gilbert E. Detillieux) The Manitoba UNIX User Group (MUUG) will be holding its next monthly meeting on Tuesday, December 11. The meeting topic for this month is as follows: Using Kickstart to Install Red Hat Linux Systems According to Red Hat, ``Many system administrators would prefer to use an automated installation method to install Red Hat Linux on their machines. To answer this need, Red Hat created the kickstart installation method. Using kickstart, a system administrator can create a single file containing the answers to all the questions that would normally be asked during a typical Red Hat Linux installation.'' ``Kickstart files can be kept on single server system, and read by individual computers during the installation. This installation method can support the use of a single kickstart file to install Red Hat Linux on multiple machines, making it ideal for network and system administrators.'' This month, John Schulz, from Pollard Banknote Ltd., will present a quick overview of Kickstart and demo the install process. The group holds its general meetings at 7:30 PM on the second Tuesday of every month from September to June. (There are no meetings in July and August.) Meetings are open to the general public; you don't have to be a MUUG member to attend. ********************************************************************** New Location: Once again this month, and from now on, the meeting will be at the IBM offices, at 400 Ellice Ave. (between Edmonton and Kennedy). When you arrive, you will have to sign in at the reception desk, and then wait for someone to take you (in groups) to the meeting room. Limited parking is available for free on the street, or in a lot across Ellice from IBM, for $1.00 for the evening. Indoor parking is also available nearby, at Portage Place, for $2.00 for the evening. ********************************************************************** For more information about MUUG, and its monthly meetings, check out their Web server: http://www.muug.mb.ca/ Also note that MUUG maintains two mailing lists, called "muug-announce" and "roundtable". If you're not already on these lists, I encourage you to subscribe now: http://www.muug.mb.ca/mailman/listinfo/ The "muug-announce" list is used for monthly meeting announcements (such as this one) as well as other important announcements of interest to MUUG members. The "rountable" list is meant to be a forum for follow-ups to topics discussed at the meetings, or for round-table-style discussion on other topics that come up between meetings. Of course, for this to be effective, we need to reach a certain critical mass. So, please subscribe, and stay involved! -- Gilbert E. Detillieux E-mail: <gedetil(a)muug.mb.ca> Manitoba UNIX User Group Web: http://www.muug.mb.ca/ P.O. Box 130, St-Boniface Phone: (204)474-8161 Winnipeg, MB, CANADA R2H 3B4 Fax: (204)474-7609 ------ End of Forwarded Article

1 0

Shaw @home in trouble?
by author 03 Dec '01

03 Dec '01

I just read on Cnet that excite@home was going broke and that over 800,000 AT&T internet users were cut off. Does this @home have anything to do with Shaw's cable @home service? Will Shaw's internet service be interrupted? Also read on the Byte site ( www.byte.com ) about Linux being used to savage that sunken Russian sub.

3 2

Mac to PC serial
by author 22 Nov '01

22 Nov '01

Thanks Gilbert. Got files sent both ways between the MacSE and PC. The PC ( a 486 with Slackware3.6 ) will only download in Xmodem, but can send in Zmodem. The only real problem left is the PC speaker. Minicom gets it beeping after a successful upload or download, which is fine, except it doesn't turn off. It goes into a terrible howl until I exit minicom and press any key on the command line. So I disconnected the 486 speaker to save my ears and all is well. Next I want to figure out the pin connections and make a cable just for this connection. As it is now, I'm using a Mac modem cable, a Null modem cable, and a gender converter, all for this one task, which seems a waste. Thanks again!

1 0

Null modem serial connection minicom
by author 21 Nov '01

21 Nov '01

I'm trying to set up a nullmodem serial connection between a PC (Linux) and a MacSE (OS6.04). I've got some files I want to pump into the old Mac without having to mess with its floppy drive. Anyway, I've got the computers connected with the correct hardware, that is, a Mac serial modem cable pluged into a a 25 pin null modem cable. Zterm on the Mac is all set, but I'm not sure how to set up minicom for a pure serial connection. Everthing I've read about minicom is for a modem, not a serial connection. So here is the question: How do you set up minicom for a simple null modem serial connection? Any information would be appreciated.

2 1

NTP - It's about time!...
by gedetil＠cs.umanitoba.ca 20 Nov '01

20 Nov '01

(Sorry, I couldn't resist the bad pun.) Just a quick note to say I've updated the write-up of the November MUUG meeting on our web site... http://www.muug.mb.ca/meetings/ ... to include links to the web sites mentioned in the meeting, including the one for NTP. Also, someone had asked whether ntpd under Linux would update the hardware (CMOS) clock or not. It doesn't - it only deals with the system clock (the internal kernel clock that counts time elapsed since a particular epoch). Unfortunately, within Linux, those two clocks are kept independent, and can actually be keeping different time. The solution, if you want to make sure your hardware clock is at least periodically synched up to the system clock, would be to run a cron job to do this via the "hwclock" command. I've attached a simple little script that does the job, and takes things into account like whether the clock is keeping time in UTC (GMT) or local time, and whether the clock is in ARC format (used by certain Alpha-based systems) or not. The script used to run the "rdate" command to update the system clock first, but I've commented that out, since you'd obviously not want to do that if you're running NTP. -- Gilbert E. Detillieux E-mail: <gedetil(a)cs.umanitoba.ca> Dept. of Computer Science Web: http://www.cs.umanitoba.ca/~gedetil/ University of Manitoba Phone: (204)474-8161 Winnipeg, MB, CANADA R3T 2N2 Fax: (204)474-7609

1 0

Re: [RndTbl] how do you install a adaptec ava1505 scsi controller
by gedetil＠cs.umanitoba.ca 20 Nov '01

20 Nov '01

According to S/C Conway: > What is the process to install a scsi controller in RedHat 7.1? I have a > workstation loaded and operational. I tried installing a SCSI controller > (i/o=0x140, Int=10) to host a Sony CDROM burner with no success.The > parameters are jumpered on the board. I tried installing the card from a > complete new linux installation and also tried installing the card after > the OS is up and running. No success either way. The card does not appear > to be detected. RedHat indicates the card is supported using aha152x > driver. I'm not familiar with this card. Is it an ISA bus card, or PCI bus? If it's PCI bus, it should have been auto-detected and configured correctly as long as it's a supported card. However, if it's ISA, it's possible that it won't be auto-detected, and that you'll have to set up the configuration manually. If you're sure the aha152x driver is the right one, you should be able to manually load the driver with "modprobe". If you get that far, then the following setup should work... - Add the following line to /etc/modules.conf: alias scsi_hostadapter aha152x - If you need to explictly set I/O address and/or IRQ values for the driver, then also add a line like this: options aha152x io=0x140 irq=10 (Check the driver documentation, though, as I'm not sure if these are the right options for that driver.) - Build (or rebuild) your initrd file for the kernel: mkinitrd /boot/initrd-2.4.9-12.img 2.4.9-12 (Adjust the numbers above to match those for your installed kernel.) - If not already done, add an initrd statement in /etc/lilo.conf: initrd=/boot/initrd-2.4.9-12.img (This should be after the "image=" line for the kernel to be booted.) - Run "lilo", and reboot. The reason for the slightly convoluted setup is that Red Hat configures its kernels to load the SCSI driver as a module, but that module has to be made available in an "initrd" file (initial ramdisk image), in case the system is installed on a SCSI disk drive, in which case the file system wouldn't be accessible until the driver is loaded. (Sort of a catch 22 bootstrapping problem.) Because of the way Red Hat sets this up, you still need to do it this way, even if you're not using the SCSI driver to access your system disk. > The card works. It now hosts a SCSI scanner and CDROM burner in a windows > box. If I can successfully install the card I hope to eliminate that > windows box. > > I was hoping someone had some experience with this type of installation > and might offer a stepped process to success. As I said, I'm not familiar with your card, but the above setup has worked for me for a number of cards, both ISA and PCI bus based. (Although I've never had to override I/O or IRQ settings with an options statement.) -- Gilbert E. Detillieux E-mail: <gedetil(a)cs.umanitoba.ca> Dept. of Computer Science Web: http://www.cs.umanitoba.ca/~gedetil/ University of Manitoba Phone: (204)474-8161 Winnipeg, MB, CANADA R3T 2N2 Fax: (204)474-7609

1 0

Screen Resolutions in RH 7.1
by Geek 19 Nov '01

19 Nov '01

Ok, this will be simultaneously posted in three different lists,m the TuxTalk list, the Talkabout mail list, and the MUUG Round Table list. Hopefully between these three resources I will find an adequate solution. I finally got a nicely running install of Red Hat 7.1 today, after much hassle and great help from those I know. The problem now is that the screen resolution is too small, and the GUI(KDE) looks quite grainy. After the install it was at 640x480, and a little run through of Xconfigurator brought it up to 800x600, but it is still not to what I am either used to or like. I want either 1024x768 or 1152x800. This is the last issue that needs to be resolved before I try to migrate to Linux as much as possible, with only absolutely necessary stuff being done in Windows. I tried various different sites, like Google and the Linux documentation project, but I have been unable to get a satisfactory resolution. Thanks in advance for your help, and I will post the best and most effective solution on all of these lists as soon as one is found. Thanks a lot in advance. New Blog online http://blog.geeksworld.net/ ****Finally back online http://www.geeksworld.net *****

2 1

LinuxNews.com
by Ian T. 16 Nov '01

16 Nov '01

In the article below (see the link), I'm unclear as to what he is referring to as Red Hat's "proprietary directory technology". If anyone has read the article or cares to follow up and comment, I'd appreciate it. I'd like to more information regarding these issues. If people have links to similar content please post it or contact me directly. ========================== Microsoft `Gets It': Does the Linux Community? - LinuxNews.com Features Posted by Dr. G.W. Wettstein on Thursday October 05 2000 @ 01:49PM MDT In light of all this, you can imagine our surprise and ultimate dismay when we see a major Open-Source player such as Red Hat choose to embrace proprietary directory technology. It's either a matter of not understanding the issue, not appreciating the issue, or having non-technology issues drive the corporate decision making process. ==========================-- Cheers! Ian. N 49 12' 30" W 96 53' 45"

1 0

how do you install a adaptec ava1505 scsi controller
by S/C Conway 16 Nov '01

16 Nov '01

What is the process to install a scsi controller in RedHat 7.1? I have a workstation loaded and operational. I tried installing a SCSI controller (i/o=0x140, Int=10) to host a Sony CDROM burner with no success.The parameters are jumpered on the board. I tried installing the card from a complete new linux installation and also tried installing the card after the OS is up and running. No success either way. The card does not appear to be detected. RedHat indicates the card is supported using aha152x driver. The card works. It now hosts a SCSI scanner and CDROM burner in a windows box. If I can successfully install the card I hope to eliminate that windows box. I was hoping someone had some experience with this type of installation and might offer a stepped process to success. Sean

1 0

MUUG Meeting, November 13, 7:30PM -- Mini-HOWTO's on NTP and XINETD
by gedetil＠cs.umanitoba.ca 06 Nov '01

06 Nov '01

[Posted to man.unix.general and other news groups] ------ Forwarded Article <9s9813$b57$1(a)canopus.cc.umanitoba.ca> ------ From gedetil(a)cs.umanitoba.ca (Gilbert E. Detillieux) The Manitoba UNIX User Group (MUUG) will be holding its next monthly meeting on Tuesday, November 13. The meeting topic for this month is as follows: Mini-HOWTO's on NTP and XINETD This month, MUUG members Kevin McGregor and Gilbert Detillieux will each be covering a short topic, in a mini-HOWTO format. Kevin McGregor will be talking about NTP, the network time protocol, and the UNIX daemon which provides support for this protocol. Gilbert Detillieux will be talking about XINETD, a powerful replacement for the UNIX INETD daemon, used for launching numerous TCP and UDP based network services. The group holds its general meetings at 7:30 PM on the second Tuesday of every month from September to June. (There are no meetings in July and August.) Meetings are open to the general public; you don't have to be a MUUG member to attend. ********************************************************************** New Location: Once again this month, and from now on, the meeting will be at the IBM offices, at 400 Ellice Ave. (between Edmonton and Kennedy). When you arrive, you will have to sign in at the reception desk, and then wait for someone to take you (in groups) to the meeting room. Limited parking is available for free on the street, or in a lot across Ellice from IBM, for $1.00 for the evening. Indoor parking is also available nearby, at Portage Place, for $2.00 for the evening. ********************************************************************** For more information about MUUG, and its monthly meetings, check out their Web server: http://www.muug.mb.ca/ Also note that MUUG maintains two mailing lists, called "muug-announce" and "roundtable". If you're not already on these lists, I encourage you to subscribe now: http://www.muug.mb.ca/mailman/listinfo/ The "muug-announce" list is used for monthly meeting announcements (such as this one) as well as other important announcements of interest to MUUG members. The "rountable" list is meant to be a forum for follow-ups to topics discussed at the meetings, or for round-table-style discussion on other topics that come up between meetings. Of course, for this to be effective, we need to reach a certain critical mass. So, please subscribe, and stay involved! -- Gilbert E. Detillieux E-mail: <gedetil(a)muug.mb.ca> Manitoba UNIX User Group Web: http://www.muug.mb.ca/ P.O. Box 130, St-Boniface Phone: (204)474-8161 Winnipeg, MB, CANADA R2H 3B4 Fax: (204)474-7609 ------ End of Forwarded Article

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

Roundtable