Roundtable

roundtable@muug.ca

2555 discussions

Ryzen + ECC
by Trevor Cordes 16 Nov '17

16 Nov '17

To follow up on the in-meeting roundtable the other day: I found some newer reports that ECC can work on Ryzen, if the stars are aligned. http://www.hardwarecanucks.com/forum/hardware-canucks-reviews/75030-ecc-mem… Basically says they got to the stage where EDAC in linux recognized the ECC and could get single-bit errors generated and logged. That's all I'm interested in, really (double-bit errors don't concern me as much, esp if they're still logged). So this looks promising. Looks like you have to be quite selective in mobo, and the one they tested was: ASRock X370 Taichi (not cheap!) I wouldn't buy a Ryzen mobo for ECC support unless someone had already tested it like they did to confirm it supports ECC. So it's nice to see it is possible, though the support & guarantees are pretty dodgy. Ah, back to the good (bad) ol' days (2000-2005) of VIA chips and Intel boards that maybe/maybe-not had ECC that actually did something. === If you want guaranteed (validated) ECC on Ryzen, looks like you go with the recently released Ryzen Threadripper 8c/16t CPUs and HEDT "high-end desktop" boards. However, then you are looking at prices like Intel "workstation" products, though you will get more threads/buck. Personally, I don't have a use for tons of threads (yet), so for me a lower-end Xeon with a workstation board might on the table again, unless I want to take the risk with a maybe/might/should-work regular Ryzen. Adam's article (coming soon!) on Ryzen random mem latency for routing might be the straw that breaks the Ryzen camel back for me. We'll see... As always, if someone beats me to building (from parts) an ECC *workstation* (i.e. real, full x16 slot) in '17 or '18, post your results here!!

1 0

MUUG Meeting, Nov. 14, 7:30pm -- AGM, MacPorts, Linux Containers using LXD
by Gilbert E. Detillieux 07 Nov '17

07 Nov '17

*** Please note the updated meeting location below *** The Manitoba UNIX User Group (MUUG) will be holding its next monthly meeting on Tuesday, November 14. The meeting topic for this month is as follows: Linux Containers using LXD LXD is a next-generation system container manager, which offers a user experience similar to virtual machines but using Linux containers instead. Kevin McGregor will be presenting an introduction to basic Linux containers using LXD on Ubuntu. RTFM: MacPorts Adam Thompson will present and demonstrate MacPorts, one of the systems used for compiling, installing and upgrading command-line, X11 or Aqua based open-source software on the Mac operating system. AGM Plus, this month's meeting was the MUUG annual general meeting, which included the election of the MUUG board of directors for the 2017-2018 year (by acclamation). The group usually holds its meetings at 7:30pm on the second Tuesday of every month from September to June. (There are no meetings in July and August.) Meetings are open to the general public; you don't have to be a MUUG member to attend. ******************************************************************* Please note our *NEW* meeting location for this month: *Room 1C16A* Centennial Hall, University of Winnipeg, entrance on Ellice Ave. between Spence St. and Balmoral St. Parking is available on the surrounding streets and in the lots on nearby streets. Look for signage once you're at the building, or ask a security guard. ******************************************************************* For more information about MUUG, and its monthly meetings, check out their web server: https://muug.ca/ Help us promote this month's meeting, by putting this poster up on your workplace bulletin board or other suitable public message board: https://muug.ca/meetings/MUUGmeeting.pdf -- Manitoba UNIX User Group E-mail: <gedetil(a)muug.ca> c/o Gilbert E. Detillieux Web: http://muug.ca/ University of Manitoba Phone: (204)474-8161 Winnipeg MB CANADA R3T 2N2 Fax: (204)474-7609

1 0

MUUG.ca mirrors down
by Trevor Cordes 04 Nov '17

04 Nov '17

FYI, MUUG.ca had a catastrophic disk failure that led to a pathological situation causing loss of the mirror array. The mirror data will likely be unavailable for a few days. The web site and mailing lists and other services should continue to function perfectly. We'll renotify here when the mirrors are back up. Thanks for your patience!

1 0

Linux Help
by Mike Zettler 24 Oct '17

24 Oct '17

Hello MUUG! We are a small MSP in Winnipeg, we have a few customers with Linux servers and I don't have any Linux expertise on-staff. Would like to hire someone for a ½ day or so to check a few things on the servers, maybe re-configure. Can some contact me? Thank you! Mike Z. Mike Zettler Vice President of Operations| 365 Technologies Inc. 555 Plinguet Street, Winnipeg, MB R2J 0G2 O: 204.488.3655 Ext. 21|M: 204.803.7575 |E: MikeZ(a)365tech.ca<mailto:MikeZ@365tech.ca> Follow us on Twitter @365tech<http://twitter.com/365tech> [Description: Description: 365_WorryFreeIT] Our clients get results - read their stories here<http://www.365tech.ca/results.cfm> [Description: Description: MS Small Business Specialist-hi res] [http://www.oxford-knowledge.com/wp-content/uploads/2012/08/VMW_09Q4_LGO_PAR…] [http://dev.logikalteks.com/wp-content/uploads/2013/07/Dell_PreferredPartner…] Our Emails are intended to communicate, educate, and transfer information. Sometimes, these Emails qualify as Commercial Electronic Messages (CEM) under CASL. If you would prefer not to receive these Emails anymore, please click HERE<mailto:unsubscribe@365tech.ca?subject=Unsubscribe> or Email unsubscribe(a)365tech.ca<mailto:unsubscribe@365tech.ca> with the Subject 'Unsubscribe'.

1 0

Small router box
by Kevin McGregor 20 Oct '17

20 Oct '17

Hey all, Maybe someone can remember the device I'm trying to recall. It's from a company that makes small devices which can run Linux and they come either as a bare board or in a small metal box with some number of ethernet ports. It's not ARM-based. I know that's vague, but surely some of you can come up with a list which will contain the one I'm trying to remember! Or something comparable, at least. Oh, and they used to advertise in Linux Journal. I'm not sure if they're still in business.

8 9

Fwd: Re: [macports-mgr] Would like to add new mirror
by Adam Thompson 16 Oct '17

16 Oct '17

FYI: MUUG now provides a MacPorts mirror. As always, let us know if there's any distros or software you'd like us to mirror (that is at least tangentially UNIX-related, preferably). -Adam -------- Original Message -------- From: "Rainer Müller" <raimue(a)macports.org> Sent: October 15, 2017 1:02:53 PM CDT To: Adam Thompson <athompso(a)athompso.net> Cc: macports-mgr(a)lists.macports.org Subject: Re: [macports-mgr] Would like to add new mirror [...] I added the DNS entries and the mirrors to the wiki page: https://trac.macports.org/wiki/Mirrors?action=diff&version=95 The mirror URLs for distfiles and packages are now also live: https://github.com/macports/macports-ports/commit/e85e0350ed3ac015fd822ad29… Thank you for providing the mirror for MacPorts! Rainer -- Sent from my Android device with K-9 Mail. Please excuse my brevity.

1 0

Unix command line challenge!
by Kevin McGregor 13 Oct '17

13 Oct '17

Given a gzipped cpio archive (12 GB!) with files in it like: wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/CILICEXP.xml wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/CILTSVTP.xml wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/C1LOOUPP.xml wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/CILTTRAL.xml wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/CILCSSPL.xml wwdsvdccb101/root/data/ccb/ccbx/splapp/servers/myserver/tmp/.appmergegen_1347913274622/SPLWeb.ear/h7y1ba/data/xml/CILTCLGP.xml How can I change the first component of the path to something else without unpacking the entire archive to disk first? Obviously I'll still have to un-gzip and de-cpio the whole 12GB while processing; I just don't want to put the whole thing on disk while I'm changing the path. Any ideas? Kevin

3 3

MUUG Meeting, Oct. 10, 7:30pm -- Kid3, VLAN Theory and Implementation
by Gilbert E. Detillieux 10 Oct '17

10 Oct '17

*** Please note the updated meeting location below *** The Manitoba UNIX User Group (MUUG) will be holding its next monthly meeting on Tuesday, October 10. The meeting topic for this month is as follows: VLAN Theory and Implementation VLANs (Virtual Local Area Networks) allow you to partition a physical network at the data link layer, "creating the appearance and functionality of network traffic that is physically on a single network but acts as if it is split between separate networks." (Wikipedia) VLAN tagging (IEEE 802.1Q) allows traffic from multiple VLANs to travel between Ethernet switches over the same physical link. In this presentation, Gilbert Detillieux will introduce some of the basic concepts of VLAN setup, and show you how this can be implemented. Examples of implementation will be given using Cisco IOS commands and typical Linux network interface configuration. RTFM: Kid3 This month, Wyatt Zacharias will present and demonstrate Kid3, the KDE ID3 tag editor. The group usually holds its meetings at 7:30pm on the second Tuesday of every month from September to June. (There are no meetings in July and August.) Meetings are open to the general public; you don't have to be a MUUG member to attend. ******************************************************************* Please note our *NEW* meeting location for this month: *Room 1C16A* Centennial Hall, University of Winnipeg, entrance on Ellice Ave. between Spence St. and Balmoral St. Parking is available on the surrounding streets and in the lots on nearby streets. Look for signage once you're at the building, or ask a security guard. ******************************************************************* For more information about MUUG, and its monthly meetings, check out their web server: https://muug.ca/ Help us promote this month's meeting, by putting this poster up on your workplace bulletin board or other suitable public message board: https://muug.ca/meetings/MUUGmeeting.pdf -- Manitoba UNIX User Group E-mail: <gedetil(a)muug.ca> c/o Gilbert E. Detillieux Web: http://muug.ca/ University of Manitoba Phone: (204)474-8161 Winnipeg MB CANADA R3T 2N2 Fax: (204)474-7609

2 1

Looking for some AWK magic
by Wyatt Zacharias 24 Sep '17

24 Sep '17

So I've got a storage appliance that I'm trying to generate a growth chart on, but the output format of the statistics is not in a usable format. The output looks like this, with each day of the week in a column, and then 6 rows of data underneath, and then it repeats. -2- -3- -4- -5- -6- -7- -8- 5827.1 6865.6 3551.2 4649.5 4006.6 15803.5 10305.0 199.4 353.4 175.9 200.7 172.5 584.0 554.2 9.9x 4.4x 6.4x 5.9x 6.3x 5.6x 5.3x 3.0x 4.4x 3.2x 3.9x 3.7x 4.9x 3.5x 29.2x 19.4x 20.2x 23.2x 23.2x 27.1x 18.6x 96.6 94.9 95.0 95.7 95.7 96.3 94.6 -23- -24- -25- -26- -27- -28- -29- 2798.2 2235.3 2357.9 4701.3 9074.3 13796.5 11705.7 86.7 74.1 131.6 178.1 449.3 483.5 473.7 11.4x 12.0x 7.0x 8.1x 3.9x 6.3x 6.7x 2.8x 2.5x 2.6x 3.2x 5.2x 4.6x 3.7x 32.3x 30.2x 17.9x 26.4x 20.2x 28.5x 24.7x 96.9 96.7 94.4 96.2 95.0 96.5 96.0 -30- -31- -1- -2- -3- -4- -5- 2798.6 2274.5 2325.8 2472.1 2526.0 13955.3 11224.2 86.7 88.9 145.2 115.2 105.6 497.9 432.4 10.8x 10.1x 7.4x 8.1x 9.8x 6.2x 6.9x 3.0x 2.5x 2.2x 2.7x 2.4x 4.5x 3.8x 32.3x 25.6x 16.0x 21.5x 23.9x 28.0x 26.0x 96.9 96.1 93.8 95.3 95.8 96.4 96.1 Is there a way I can get awk to process 6 rows of each column at a time? -- Wyatt Zacharias

4 3

Re: [RndTbl] Roundtable Digest, Vol 153, Issue 6
by Michael Doob 21 Sep '17

21 Sep '17

On the other hand awk has 1. a variable NR the contains the current line number 2. a % operator that can be used to compute modulo 7 3. a getline command that reads the next line of input That's all you need. Cheers, Michael ------------------------------------------------------------------ Michael Doob Telephone: (204) 474-9796 Department of Mathematics email: Michael.Doob(a)UManitoba.ca University of Manitoba Winnipeg, MB, Canada R3T 2N2 ------------------------------------------------------------------ ________________________________________ From: Roundtable <roundtable-bounces(a)muug.ca> on behalf of roundtable-request(a)muug.ca <roundtable-request(a)muug.ca> Sent: September 21, 2017 1:23:52 PM To: roundtable(a)muug.ca Subject: Roundtable Digest, Vol 153, Issue 6 Send Roundtable mailing list submissions to roundtable(a)muug.ca To subscribe or unsubscribe via the World Wide Web, visit https://muug.ca/mailman/listinfo/roundtable or, via email, send a message with subject or body 'help' to roundtable-request(a)muug.ca You can reach the person managing the list at roundtable-owner(a)muug.ca When replying, please edit your Subject line so it is more specific than "Re: Contents of Roundtable digest..." Today's Topics: 1. Looking for some AWK magic (Wyatt Zacharias) 2. Re: Looking for some AWK magic (Sean Cody) 3. Re: Looking for some AWK magic (John Lange) ---------------------------------------------------------------------- Message: 1 Date: Thu, 21 Sep 2017 12:01:33 -0500 From: Wyatt Zacharias <wyatt(a)magitech.ca> To: Continuation of Round Table discussion <roundtable(a)muug.ca> Subject: [RndTbl] Looking for some AWK magic Message-ID: <CANd2pR2wwERFj2R6_JswyzT91cpnq+RM7KhgC1goP6CEbbJoiQ(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" So I've got a storage appliance that I'm trying to generate a growth chart on, but the output format of the statistics is not in a usable format. The output looks like this, with each day of the week in a column, and then 6 rows of data underneath, and then it repeats. -2- -3- -4- -5- -6- -7- -8- 5827.1 6865.6 3551.2 4649.5 4006.6 15803.5 10305.0 199.4 353.4 175.9 200.7 172.5 584.0 554.2 9.9x 4.4x 6.4x 5.9x 6.3x 5.6x 5.3x 3.0x 4.4x 3.2x 3.9x 3.7x 4.9x 3.5x 29.2x 19.4x 20.2x 23.2x 23.2x 27.1x 18.6x 96.6 94.9 95.0 95.7 95.7 96.3 94.6 -23- -24- -25- -26- -27- -28- -29- 2798.2 2235.3 2357.9 4701.3 9074.3 13796.5 11705.7 86.7 74.1 131.6 178.1 449.3 483.5 473.7 11.4x 12.0x 7.0x 8.1x 3.9x 6.3x 6.7x 2.8x 2.5x 2.6x 3.2x 5.2x 4.6x 3.7x 32.3x 30.2x 17.9x 26.4x 20.2x 28.5x 24.7x 96.9 96.7 94.4 96.2 95.0 96.5 96.0 -30- -31- -1- -2- -3- -4- -5- 2798.6 2274.5 2325.8 2472.1 2526.0 13955.3 11224.2 86.7 88.9 145.2 115.2 105.6 497.9 432.4 10.8x 10.1x 7.4x 8.1x 9.8x 6.2x 6.9x 3.0x 2.5x 2.2x 2.7x 2.4x 4.5x 3.8x 32.3x 25.6x 16.0x 21.5x 23.9x 28.0x 26.0x 96.9 96.1 93.8 95.3 95.8 96.4 96.1 Is there a way I can get awk to process 6 rows of each column at a time? -- Wyatt Zacharias

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

Roundtable